FREQROL FR SF PDF

GENERAL. Usage of Maintenance Manual. FR-SF series inverters are designed to drive machine tool spindles, and feature quiet operation, stable and rapid. Hi all: Could anyone please explain the difference between the FREQROL FR- SE and FR-SF??? To me they sound the same I thank you for. Repair service for FR-SFK-CE Mitsubishi AC Spindle Drive 26kW VAC FREQROL FR-SF Condition: Send-in repair. Free evaluation. 6 Months warranty .

Author: Mazudal Misar
Country: Australia
Language: English (Spanish)
Genre: Politics
Published (Last): 5 April 2011
Pages: 451
PDF File Size: 18.92 Mb
ePub File Size: 7.1 Mb
ISBN: 837-8-70150-971-7
Downloads: 54247
Price: Free* [*Free Regsitration Required]
Uploader: Kigasho

For the main circuit cable size for the motor, see Appendix 3 [ l Main circuit cables]. Amazon Restaurants Food delivery from local restaurants.

Mitsubishi AC Spindle Drive FREQROL-SF Maintenance Manual pdf – CNC Manual

The input signal from 0 Check each bit of a control xf Conduct the same counter- the NC is abnormal. See Appendix 3 2. For details of the contents of alarms, see 1.

Set to adjust orientation for the respective gear. I purchased some a year or so ago and they were new Darameter settina 2 Check terminals See Appendix g 2. Stop position is set within 0 – – range from -5 deg. Since the parameter is cleared when the power is turned off or reset, after it is set to “l”, input the speed reference and start command. Between CH23 – CH9: I have swopped them arround and I still get the same Alarm. SF-TL card or SF-CA card The backlash of the o In the multiple point orien- o Decrease the backlash of the portion where the en- tation operation, check that portion where the encoder is coder is mounted is the stop position of the for- mounted.

  HOW TO BE A MENTALIST WINTHROP PDF

Started machine again with the door of the spindle drive still open. The Ki magnification should be set to the magnification for VKI.

Login to Your Account. Amazon Rapids Fun stories for kids on the go. For gear 01, the number of gear teeth: Rebuild of your existing Mitsubishi spindle drive at competitive prices!

Mitsubishi AC Spindle Drive FREQROL-SF Maintenance Manual

Encoder Magnesensor Spindle The spindle rotational angle at which orienta- creep speed starts is set. It seems I found a typo or two in the charts that caused me great confusion.

Fanuc 16i i CNC Series. For pin settings in the table, means that the pin is to be inserted; g mean hat the pin is Cl to be removed. At the time, the fan case with the cooling fan can be dismounted. The power cable into the machine had a wire broken. I cuit board M? Check that it rotates for 10 turns until it comes to the hole bottom and returns to the start position. This parameter is set when the orientation should be adjusted by each gear. Whether to open the trouble signal contact FA-FC can be selected with a parameter.

Position loop IN after orientation 1: See Appendixes l-4 and l-5 When they are shortcircuited D At a convenient time, re- the thermal protector is place the motor with a new normal. How much life can be le Otherwise, the equipment may be damaged. Rotate the motor at the maximum speed and check that the amplitudes of the signal outputs for the forward rotation and reverse rotation are? Note When mounting the card, by pushing the connec- tor rear side from the front side with your fingers and check that the connector is securely connected to the card.

  ABLOY EL412 PDF

Is there a fuse or trip switch stopping the controller coming on? OH is regarded as 1 time. El – 00 Fig.

Does the trouble or fault differ between the forward rotation and reverse rotation? Sorted that now and screen and controller back up. Note Before using the check pins, the power of the amplifier should have been turned off. If it continues to be run with transistors not firing properly it will eventually take out the first transistor to fire after xf transistor that wasn’t working.

Parameter Description Encoder orientation: Software timer d When the slow down timer software timer. Refurbished by Mitsubishi Electric Automation. This item was removed from aWorking Machine, and i The cable connections 3 Visually check the cable con- 3 Correctly connect the between the amplifier nections.

CCw Hotor forward rotation Note While the equipment is linked with the NC using analog signal or digital signal, 09 tr to set TLl and TL2, which ft usually used as torque control input signals, as indexing input signals.

Mitsubishi Freqrol FR-SF

On the other hand, when the equipment ‘is linked with the machine through the bus line, part of parameters can be set from the NC. Cl – EO Parameter 4: There are two different guys from Malaysia selling them on Ebay.

When the equipment linked with the NC through is linked through the bus is set. The servo rigidity is weak. Appendix frwqrol or l