within 72 hours in accordance with ASTM E “Standard Test Method for specification compliance in ASTM E “Standard Practice for Using. industry references The American Society for Testing Materials (ASTM) Standard. E, “Practice for Using Significant Digits in Test Data to Determine. ASME中国制造-ASTM E (原文)_化学_自然科学_专业资料。Designation: E29? 13 An American National Standard Standard Practice for.

Author: Tygozil Fenrijind
Country: Greece
Language: English (Spanish)
Genre: Photos
Published (Last): 16 December 2005
Pages: 225
PDF File Size: 20.67 Mb
ePub File Size: 2.63 Mb
ISBN: 694-1-93337-454-2
Downloads: 74561
Price: Free* [*Free Regsitration Required]
Uploader: Gat

For example, the numbers Users of this standard are qstm advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. The examples are not binding on products or test methods treated.

The number of signi?

Multiplying 4 by 0. Table 1 gives examples of applying this rounding procedure. Zeros trailing the last nonzero digit for numbers represented with a decimal point are signi? ASTM does not give any warranty express or implied or make any representation that the contents of asttm abstract are accurate, complete or up to date.

Excel: Round 0.5 towards Even Per ASTM-E29

d29 Work Item s – proposed revisions of this standard. It should not be inferred that a measurement value is precise to the number of signi? In such cases, the following procedure can be used for rounding to any interval: Dimensional quantities in the practice are presented only as illustrations of calculation methods. Any approach to retention of signi?

This will be referred to as the rounding method,which is discussed in Section 6. Write down the standard deviation. The following guidelines are aastm to preserve the data for statistical summaries.


Excel: Round towards Even Per ASTM-E29 – Excel Articles

That is, the rounding unit for the speci? ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

It is informational only and not an official part of atm standard; the full text of the standard itself must be referred to for its use and application. This will be referred to as the absolute method, which is discussed in Section 5. This standard has been approved for use by agencies of the Department of Defense. Guidelines for Retaining Signi? If you feel that your comments have not received a fair hearing you should make your views known to astn ASTM Committee on Standards, asttm the address shown below.

The conversion constant, Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. ASTM Manual 7 provides methods for reporting x? ICS Number Code Round test results to the place of the?

Reporting s to within 0. Historical Version s – view previous versions of standard Work Item s – proposed revisions of this standard Translated Version s: In the applications of this practice to a speci?

This practice is intended to assist the various technical committees in the use of uniform methods of indicating the number of digits which are to be considered significant in specification limits, for example, specified maximum values and specified minimum values.

This abstract is a brief summary of the referenced standard. For example, the number 0. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.


ASME中国制造-ASTM E (原文)_百度文库

Tensile Adtm Tensile strength, psi Yield point, min, psi Elongation in 2 in. Digits of ln x or log10 x are signi? For example, in rounding 6 to the nearest 50, 6 is doubled giving 12 which becomes 12 when rounded to the nearest 6.

For certain purposes, such as where calculations involve differences of measurements close in magnitude, and for some statistical calculations, such as paired t-tests, autocorrelations, and nonparametric tests, reporting data to a greater number of signi?

Dimensional quantities in the practice are presented only as illustrations of calculation methods. For example, a modulus strength, stated as Pa, may have as few as two or as many as six signi?

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

When 12 is divided by 2, the resulting number, 6is the rounded value of 6 Historical Version s – view previous versions of standard. When the measuring device has a vernier scale, the last digit recorded is the one from the vernier. As far as is practicable with the calculating device or form used, carry out calculations with the observed values exactly and round only the?

Permission rights to photocopy the standard may also be secured from the ASTM website www.