ASTM B Standard Guide for Post-Coating Treatments of Steel for Reducing the Risk of Hydrogen Embrittlement. ASTM B Standard Guide for Post-Coating Treatments of Steel for Reducing_ 化学_自然科学_专业资料。后电镀产品处理,降低氢脆的风险标准. Buy ASTM B R GUIDE FOR POST-COATING TREATMENTS STEEL FOR REDUCING THE RISK OF HYDROGEN.
|Published (Last):||11 November 2009|
|PDF File Size:||2.59 Mb|
|ePub File Size:||2.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
All information presented is for general reference and does not represent a professional opinion nor the policy of an author’s employer. NOTE 2—The treatment class selected is based on experience with the part, ashm similar parts, and the speci? The coating changes from an amorphous structure to a crystalline structure and no longer exhibits self-healing properties. Additionally, the selection of electroplating atm with high cathodic efficiencies is recommended for 2.
This heat treatment procedure shall be used after plating operations but prior to any secondary conversion coating operation.
This heat-treatment procedure shall be used after plating operations but prior to any secondary conversion coating operation.
B — 98 ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Per B paragraph 6. Some companies consider the high temperature bake as sufficient to replace the hydrogen embrittlement relief if it can be done within 4 hours, but you would need to check with your customer b8850 before going down that route.
ASTM B733 Class 3 post heat treatment vs. ASTM B850 embrittlement relief
They do not apply to any other standard. A number in parentheses indicates the year of last reapproval. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? I’m an engineer trying to write good b8850 notes for plating requirements.
ASTM B850 – 98(2015)
Guide ASTM B is a better document to use as a guide to the minimum times for de-embrittlement operations, especially true when you get up the the high tensile strength or very hard materials.
February 24, — apologies, finishing. No further reproductions authorized. NOTE 5—The time period referred to is the length of time between the end of the plating operation and loading of the item concerned into the heat treatment processor. Preparation involving cathodic treatments in alkaline or acid solutions astn be avoided. asym
ASTM B Class 3 post heat treatment vs. ASTM B embrittlement relief
Originally approved in Hydrogen can also be introduced during fabrication, for example, during roll forming, machining, and drilling, atm to the breakdown of unsuitable lubricants, as well as during welding or brazing operations. No other units of measurement are included in this standard. This phenomenon often occurs in alloys that show no signi? This abstract is a brief summary of the referenced standard. Embrittlement Relief Treatment Classes 5.
ASTM does axtm give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Except for surface-hardened and shot-peened parts, the choice of embrittlement-relief heat treatment and the corresponding treatment conditions shall be selected on the basis of actual tensile strength of the steel. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
What is the answer to the Heat Treatment vs. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
ASTM B Standard Guide for Post-Coating Treatments of Steel for Reducing_百度文库
This heat-treatment procedure shall be used after plating operations but ast, to any secondary conversion coating operation. Historical Version s – view previous versions of standard. Let’s say that this plating has a Class 2 requirement Heat Treat for Hardnessand it also needs Hydrogen Embrittlement relief. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
The heat treatment does not guarantee complete freedom from the adverse effects of hydrogen degradation. Last previous edition approved in b8550 B — Hi Richard, If the high temperature treatment cannot be done within a reasonable time at least within 4 hours of plating then the embrittlement relief bake needs to be done first.
It’s not possible to diagnose a finishing problem or b580 hazards of an operation via these pages. Heat Treatment After Processing 6. Because of factors such as alloy composition and structure, type of coating, coating thickness, size, mass, or design parameters, some parts may perform satisfactorily with no embrittlement-relief treatment. Hi Richard, Bit of an odd one this.